Carbon-Filled Polycarbonate · Engineering Filament
3DXTECH CarbonX PC+CF - Filament Specification & Printing Guide
Engineering specifications for 3DXTECH CarbonX PC+CF, a Carbon-Filled Polycarbonate 3D printing filament with a 143°C heat deflection temperature -- covering nozzle, enclosure, and drying requirements.
- Polymer Base
- Carbon-Filled Polycarbonate
- Heat Deflection Temp
- 143°C
- Nozzle / Hotend
- Hardened Steel Required
- Enclosure
- Passive Enclosure
3DXTECH CarbonX PC+CF
3DXTECH CarbonX PC+CF is a Carbon-Filled Polycarbonate filament rated to a 143°C heat deflection temperature. This page collects its hardware, environmental, and handling requirements in one place so you can confirm your printer is up to the job before you load the spool.
Material Overview
3DXTECH CarbonX PC+CF is an engineering-grade 3D printing filament built on a Carbon-Filled Polycarbonate polymer base. With a heat deflection temperature of 143°C, it is engineered for functional parts that must hold their shape under load and elevated service temperatures — jigs, fixtures, brackets, ducting, and end-use components that would deform in a commodity material.
Selecting 3DXTECH CarbonX PC+CF is a systems decision, not just a spool decision: the polymer base dictates your hotend, your chamber, and your drying workflow. The sections below translate the manufacturer’s data into the concrete hardware and environmental requirements your printer must satisfy.
At a glance
- Polymer base: Carbon-Filled Polycarbonate
- Heat deflection temperature: 143°C
- Nozzle requirement: Hardened Steel Required
- Enclosure requirement: Passive Enclosure
Hardware & Environmental Requirements
The table below summarizes the hardware and environmental prerequisites for printing 3DXTECH CarbonX PC+CF. Always confirm final values against the manufacturer’s official technical data sheet.
| Specification | Requirement |
|---|---|
| Polymer Base | Carbon-Filled Polycarbonate |
| Heat Deflection Temperature | 143°C |
| Nozzle / Hotend | Hardened Steel Required |
| Enclosure | Passive Enclosure |
| Manufacturer TDS | Download Technical Data Sheet |
Nozzle & Hotend
3DXTECH CarbonX PC+CF is an abrasive, fibre-reinforced filament. The carbon or glass fillers will rapidly erode a soft nozzle, so a hardened steel hotend (or a carbide/tool-steel alternative) is mandatory. Expect noticeably higher extrusion torque as well, so confirm your extruder can sustain the flow before running long prints. CSV designation: Hardened Steel Required.
Enclosure & Chamber
3DXTECH CarbonX PC+CF benefits from at least a passive enclosure — a fully enclosed chassis (or a draft shield) that traps the heat from the heated bed. This slows cooling, reduces warping and edge curling, and improves interlayer adhesion. An actively heated chamber is not required, but a warm, draft-free environment materially improves results.
Frequently Asked Questions
Can I print 3DXTECH CarbonX PC+CF with a standard brass nozzle?
No. 3DXTECH CarbonX PC+CF is abrasive and will destroy a brass nozzle in short order. You must use a hardened steel (or carbide) nozzle — a tool-steel upgrade protects the hotend and keeps extrusion consistent over the life of the spool.
Does 3DXTECH CarbonX PC+CF require an enclosure?
3DXTECH CarbonX PC+CF benefits from at least a passive enclosure — a fully enclosed chassis (or a draft shield) that traps the heat from the heated bed. This slows cooling, reduces warping and edge curling, and improves interlayer adhesion. An actively heated chamber is not required, but a warm, draft-free environment materially improves results.
Does 3DXTECH CarbonX PC+CF need to be dried before printing?
Polycarbonate absorbs moisture readily. Dry at 80 °C for 4-6 hours before use, and store it sealed with desiccant. Printing damp PC causes steam voids, poor layer bonding, and a cloudy finish.